Space Hardware Marketplace

GEORIX GNSS Receiver

• Supported GNSS signalsGPS C/A on L1, Galileo E1 B/C
• Signal processing hardwareDedicated RF and Mixed-Signal ASICs plus AGGA-4 ASIC
• Position accuracy in GEO20.0 m 3D rms

Multi-constellation GNSS receiver for GTO/GEO missions with better than 20 m on-board real-time navigation accuracy in GEO.

FoX NavRIX GNSS Receiver

• Supported GNSS signalsGPS L1 C/A, GPS L2C, GPS L5 I/Q, Galileo E1 B/C, Galileo E5a I/Q, Galileo E6 B/C (optional)
• On-board position accuracy< 1.0 m 3D rms
• On-board velocity accuracy< 2 mm/s 3D rms

Next-generation multi-frequency, multi-constellation GNSS receiver built on commercial components, with optional subscription-free PPP.

PODRIX GNSS Receiver

• Supported GNSS signalsGPS L1 C/A, GPS L2C, GPS L5 I/Q, Galileo E1 B/C, Galileo E5a I/Q, Galileo E6 B/C (optional)
• On-board position accuracy< 1.0 m 3D rms
• On-board velocity accuracy< 2 mm/s 3D rms

High-performance spaceborne GNSS receiver with real-time navigation below 20 cm and Precise Orbit Determination to a few centimetres.

LEORIX GNSS Receiver

• Supported GNSS signalsGPS L1 C/A, Galileo E1 B/C
• On-board position accuracy1.0 m 3D rms
• On-board velocity accuracy2 mm/s 3D rms

Multi-constellation single-frequency GNSS receiver for LEO with on-board real-time navigation accuracy below one metre.

CubeDynA

• Supported platforms1U to 12U CubeSats
• Test modeClosed-loop ADCS testing

Ground testing equipment for CubeSat ADCS closed-loop testing.

eON NEXUS

• Base capabilityAll eON HOME navigation and guidance capabilities
• Conjunction assessmentOnboard and real-time
• ManeuversAutonomous avoidance maneuver planning and execution

Autonomous collision avoidance system for satellites.

eON HOME

• Orbit determinationOnboard, from GNSS measurements
• GuidanceOnboard trajectory computation and maneuver planning
• Cooperative navigationVia inter-satellite link (ISL)

Autonomous guidance and navigation unit for Earth-orbit satellites.

IDE1140

The IDE1140 (previously VA140) is a 64 channel low-noise/low power high dynamic range charge sensitive preamplifier-shaper circuit, with…

IDE1180 AMADEUS

The IDE1180 is an application specific integrated circuit (ASIC), which has been designed for the front-end readout of…

VASCM3.2

• Channels128

The VASCM3.2 is a 128 channel low-noise/low power current sensitive preamplifier-filter circuit, with two-channel alternating sample and hold.

VA32HDR14.2

• Number of channels32

32-channel and high dynamic range charge sensitive preamplifier-shaper circuit, with sample and hold, multiplexed analog readout and calibration…

VA32HDR14.3

• Number of channels33
• Typecharge sensitive preamplifier-shaper circuit

33-channel and high dynamic range charge sensitive preamplifier-shaper circuit, with sample and hold, multiplexed analog readout and calibration…

IDE3160

The IDE3160 (previously VATA160) is an application specific integrated circuit (ASIC), which has been designed for the front-end…

VATAGP7.1

• Number of channels128

128-channel general-purpose charge-sensitive amplifier. Each channel features buffered preamplifiers, a shaper with sample/hold, multiplexed analogue readout and calibration…

VATAGP8

The VATAGP8 is an integrated circuit that allows one to measure the charge from radiation sensors.

VATA64HDR16.2

The VATA64HDR16.2 is a 64-channel charge sensitive amplifier for SiPM read-out.

IDE3465

• Channels20
• Digital logic trigger outputs37
• Analog multiplexer outputone

20-channel charge sensitive preamplifier-shaper circuit with a total of 37 digital logic trigger outputs and one analog multiplexer…

IDE3466

The IDE3466 (also VATA466) is an application specific integrated circuit (ASIC), which has been designed for the p-side…